Quest Diagnostics QUESTEMP 36 Manual do Utilizador

QUESTempo 34 and QUESTempo 36 User Manual©3M 2013. All Rights Reserved3M Personal Safety Division3M™ QUESTemp°™Heat Stress Monitors Market Leader

Tri-sensor Calculation and Remote Cable Tri-sensor Weighted Average 6 Tri-sensor Calculation and Remote Cable The top sensor bar (sensor 1) ma

Tri-sensor Calculation and Remote Cable Wet Bulb Globe Temperature 7 Measurements The QUESTemp° 34 & 36 data logging area heat stress monito

Tri-sensor Calculation and Remote Cable Heat Index/Humidex 8 Heat Index/Humidex The Heat Index is determined using the dry bulb temperature and

Operating QUESTempº 34 & 36 View 9 Operating QUESTempº 34 & 36 Use the Up Arrow and Down Arrow keys to move the marker in the display

Operating QUESTempº 34 & 36 Print 10 • Flow: On, Off . • Index: none, ACGIH, Navy, EPRI and select either: WBGTi (indo

Displayed Items Run 11 Run The run mode begins a session in memory and logs the data. 1. Begin a session by pressing the Run/Stop key from t

Displayed Items Run 12 Screen 2: GLOBE Figure 1-10: Globe screen Screen 3: WBGTi (Indoors) WBGTo (Outdoors)

Data Logging Stay Time 13 Stay Time The screen(s) displaying stay time data appear different for each of the possible indice

Printing Serial 14 Printing The recorded data can be sent to a computer through the serial RS-232 port or to a parallel pri

Printing 15 Figure 1-20: Sample printout (page 2) Session: 3

i Table of Contents Table of Contents Introduction ...

Air Flow functionality 16 Air Flow functionality (Available using 3M’s Air Probe on QUESTempº 36 model.) Air flow is measured in meters pe

Operational Check Operating sequence 17 Operating sequence 1. Turn Flow On in the setup menu of the QUESTemp° 36. 2. Plug the Air Pr

Power options 9-Volt Alkaline Battery Replacement 18 Power options There are 3 options for powering the QUESTempº 36: a 9-volt al

Power options NiMH Battery Pack 19 NiMH Battery Pack WARNING: Recharge batteries only in a non-hazardous environment. The NiMH recha

Appendix A: Specifications 20 Appendix A: Specifications Measurements Globe temperature, dry bulb temperature, wet bulb temperatu

Appendix A: Specifications 21 Remote Sensor Bars 2 x 15pin D-sub jacks are located on the side of the unit for plugging in 1 or 2

Product markings and special conditions 22 Product markings and special conditions KEMA 04ATEX1072 X <Ex> II 2 G EEx ia IIC T3

Appendix B: Heat Exposure Tables 23 Appendix B: Heat Exposure Tables ACGIH Screening Criteria for Heat Stress Exposure. WBGT

Appendix B: Heat Exposure Tables 24 ACGIH Clothing Corrections The following clothing corrections are in degrees Celsius. When a

Appendix B: Heat Exposure Tables 25 WBGT(F) I II III IV V VI 92.0 4:50 4:10 3:30 2:55 2:15 1:30 93.0 4:25 3:50

Run ...11 Displayed It

Appendix B: Heat Exposure Tables 26 Electrical power research institute (EPRI) The recommended working hours are shown based on a

Appendix C: Accessories Air Probe Accessories 27 Appendix C: Accessories Sensor array with 2 inch globe 56-795 Sensor array with 6 i

Appendix D: Detection Management Software DMS DMS Quick overview 28 Appendix D: Detection Management Software DMS The QUESTemp° 34/36 h

Appendix D: Detection Management Software DMS Downloading your sessions in DMS 29 3. Power on the QUESTempº 36 by pressing and holding th

Appendix D: Detection Management Software DMS Viewing/Analyzing and Quick Reporting in DMS 30 Viewing/Analyzing and Quick Reporting in DMS

Appendix D: Detection Management Software DMS Reporting and Printing 31 Reporting and Printing If you are in the Data finder page, you ha

32 Appendix D Customer service Contacting 3M Instrumentation Should your 3M equipment need to be returned for repair or for recalibration, p

Personal Safety Division3M Detection Solutions1060 Corporate Center DriveOconomowoc, WI 53066ISO 9001 Registered CompanyISO 17025 Accredited Calibrati

Customer service ...32 Contacting 3M Instru

1 Introduction Up and Running overview Introduction The QUESTempº 34/36 models are portable heat stress monitors that are designed

2 Getting Started Up and Running overview Getting Started Up and Running overview 2. P

Getting Started Keypad Operation 3 Keypad Operation The unit operates using a keypad with 4 keys. The I/O Enter key responds w

Placement for Monitoring/Testing Turning On/Off and Basic Operation 4 Turning On/Off and Basic Operation To quickly get you started with the QUE

Sensors Natural Wet Bulb Thermometer 5 Sensors Natural Wet Bulb Thermometer The natural wet bulb thermometer gives an indication of the effe